Infosecdad

Marked some sold items, added a few more to the list, more to come yet.

Rota Gravels (Legacy STi style clone) are common at that size. https://www.fastwrx.com/products/rota-gravel-18x8-48-5x100

Not to enable... https://www.quickjack.com/

Rockauto has the two rear KYB outback struts for $63 each. Ideally I would replace all four if you can, but you should be ok with just the rears for a while.

She's down on the chassis dolly I built, since there is no suspension left. Just need to pull the engine and tranny and then she's about due to get hauled out, so if you need something let me know.

KYB struts are usually fine for something like this, there aren't too many decent options after 25 years.

I'm fairly certain this is what I picked up from McMaster-Carr for side feed o-rings a few years ago. Line Product Ordered Shipped Balance Price Total 1 9263K124 Chemical-Resistant Viton Fluoroelastomer O-Ring, 2.5 mm Wide, 8 mm ID, Packs of 10 1 Pack 1 0 7.16 Per Pack 7.16 2 9263K776 Chemical-Resistant Viton Fluoroelastomer O-Ring, 3.5 mm Wide, 20 mm ID, Packs of 10 1 Pack 1 0 11.62 Per Pack 11.62

I've been running a Southbend Stage 3 Daily clutch for almost five years now, matched with a Verus Forged fork and pivot ball. https://www.southbendclutch.com/clutches/FJK1001-SS-O-4271/ Picked it up slightly used and have put another 45k miles on it so far.

I think you misunderstood him. He meant "silly" as in simple device that solves a problem that people are willing to pay for; not "silly" as in you were silly to buy it. I'd buy one too if I had a newer model with start/stop, but I also wished that I can come up with the solution that people would be willing to pay for to solve this.

You may have just a broken spring or unseated from the pivot ball, gonna have to dig into it, sorry. I probably have spares if you need something. Also, if you want to go heavy (which is why I have spares): https://www.verus-engineering.com/shop/a0163a-forged-clutch-fork-wrx-1108 https://www.verus-engineering.com/shop/a0068a-billet-clutch-fork-pivot-brz-frs-gt86-wrx-366

Pretty sure the first one is part of the PCV hose: https://parts.subaru.com/p/Subaru_2009_Legacy-25L-TURBO-5AT-GT-LIMITEDOBKXT-SEDAN/Hose-Vacuum-E--5792108/49322412/99071AD140.html https://parts.subaru.com/a/Subaru_2009_Legacy-25L-TURBO-5AT-GT-LIMITEDOBKXT-SEDAN/_54102_6026546/INTAKE-MANIFOLD/B13-050-22.html The second one is part of the coolant piping: https://parts.subaru.com/p/Subaru_2009_Legacy-25L-TURBO-5AT-GT-LIMITEDOBKXT-SEDAN/Hose-Vacuum/49322374/99071AC220.html https://parts.subaru.com/a/Subaru_2009_Legacy-25L-TURBO-5AT-GT-LIMITEDOBKXT-SEDAN/_54102_6030705/WATER-PIPE-1/B13-036-03.html

Can you let us know what year/mode/engine you are working on?

I figured that was probably the case since those are the most likely to be damaged. Good luck with your search!

I have the right-side roof rail from a '06 legacy wagon. There are three pieces, the front plastic insert, the middle metal rail, and the rear plastic insert. The middle and rear parts are good, but the front plastic insert is broken. So it depends on what part you need. The plastic is getting old and brittle so it's hard to get them fully intact 20 years later.

Where are you located? I may have one, but shipping it might be a challenge.

I've used King springs for saggy butt on 4th gen wagons and on my 99 outback I'm using the heavier King lowering springs for handling. As aft as I've found they are one of the best ways to handle heavy tears.

I have King Springs for my rear struts of my '99, you could try these maybe. https://get-primitive.com/product/springs/king-overload-springs/king-spring-overload-25-1995-1999-outback-rear-springs/

Same here, have a spare running set in good shape.

The STi Genomes clean up really nice with some metal polish. Unfortunately, I didn't look at my HKS mid-pipe from Japan close enough before buying it. It's only for the HKS Super Turbo axleback which I don't have. The connections are not in the stock locations. Lesson learned, now I need to decide to either put the mid-pipe for sale or find a set of Super Turbo Mufflers to see what they sound like.

This will help with the gearing, but not push/pull. https://rallispec.com/downloads/Transmission ID Chart_Public.pdf

Not sure I can make it to ECM yet, don't know my June schedule for a bit. If can't make it, I can probably ship it to someone who is closer and going.

Now testing out the Genome STi axleback. Definitely louder than the Quad STi, with lots of crackle in 1st and 2nd off throttle, good rumble. I still like the Gandor Titanium best, those are going back on soon.

Thanks for returning with what you found. Did you go back to the original ECU or did you need to use the donor?

Yes, they were within spec so I didn't take them to a machine shop. It's been 18 months now and still going strong.

The last time I did head gaskets/timing, I measured the heads and block with a machinist's straight edge to ensure they were good because I didn't want to take them in to be decked unless they needed it.