-
Posts
149 -
Joined
Content Type
Profiles
Forums
Gallery
Everything posted by Berge56
-
fs - location: FS Reno Custom JMP VF40 *** SOLD **
Berge56 replied to JJr's topic in Member Classifieds (2005 - 2009)
Bump for a fantastic Turbo. I have 3 of Johns turbos in 3 different obxt's including my car and 2 customer's cars and they are all amazing. -
First I've heard this. Do you happen to know why the blue belt is a no no?
-
Sounds like the replacement trans has a bad temp sensor in the valve body. I would start with replacing that sensor. If you have your old Trans you could start by taking the pan off of it and locating the sensor. Then swap it into the new/used trans in the car.
-
Unless you are looking to lower the car or add spring stiffness to the ride, factory springs are just fine to reuse. If you have spring compressors and are not afraid of tackling the job, I would just get new top hats and struts and swap the springs over. I have never personally tried the loaded strut option as typically customers want to keep cost down.
-
Inner/Outer Tie Rod HELP
Berge56 replied to Jolbaru_LGT's topic in Fourth Generation Legacy (2005 - 2009)
You don't need oil seals since you are just changing the hard parts (tie rods) of the steering components. not sure what gears you are ordering, but typically you need inner and outer tie rods, new boots since your doing it with clamps or zip ties can work in a pinch, the washers can be reused or for the cost you can get new. Once you get in there you will see it's not that bad. -
Removing '05 GT Camshaft Position Sensor P0340
Berge56 replied to jmcgliss's topic in Fourth Generation Legacy (2005 - 2009)
I would only use an OEM front o2 sensor. If you want to add wideband, add it downstream with a 10 degree angle from horizontal position. I used the AEM wideband and have had great success with it. -
2005 LGT EZ30R Turbo 6mt Build
Berge56 replied to Newbie123's topic in Fourth Generation Legacy (2005 - 2009)
Great build. Looking forward to the progress! -
Also when you remove the engine make sure the TC is seated in the trans before reinstalling the engine. To do this just rotate the TC by hand while giving some slight pressure towards the transmission. Failure to making sure your TC is seated can result in a blown transmission as the TC won't be seated properly with the internal transmission pump. The picture with the photobucket water stamp on it is the incorrect depth. The top view picture shows the correct depth the TC is supposed to be seated into the transmission.
-
Cyl 4 misfire - new plugs
Berge56 replied to Mr. Electric Wizard's topic in Fourth Generation Legacy (2005 - 2009)
If you decide you don't want the zip ties anymore, Iwire makes replacement clips for like 15 bucks and you will be back in business. They even have gray and black so you don't mix up front and rear wiring. They are simple to unpin the oem clip and then slide on the new end. They have install insturctions on the website as well. https://iwireusa.com/products/ignition-coil-plug-b -
05-09 Transmission Coolant Hose
Berge56 replied to MDSubie4's topic in Fourth Generation Legacy (2005 - 2009)
Those spring clamps lose their ability to stay tight over time. you can try to reposition the clamp or swap it out with a good worm gear clamp. The hose is most likely fine, just a worn out spring clamp. -
How much milage out of a built IAG block?
Berge56 replied to Mortal2None's topic in Fourth Generation Legacy (2005 - 2009)
The RA blocks are built a little stronger and cost slightly more than the regular EJ257. Some of the key features of the RA block is as follows. Same casting as the latest EJ motors, "705" Piston crowns are 2mm thicker More support on piston wrist pins Lower amount of cantilever produced Slightly heavier pistons increase durability Same strong Con Rods as 2018 STI Overall, less prone to failure than previous STI blocks Here is the part number for the RA block: 10103AD020 -
Removing '05 GT Camshaft Position Sensor P0340
Berge56 replied to jmcgliss's topic in Fourth Generation Legacy (2005 - 2009)
In my situation I believe I replaced the cam sensor first, It was bad, but I still had the hesitation and random misfire code. Once I replaced both OCV's car drove like new again. It's been 30k miles since doing this and the car still drives great. -
I would say its most likely bad headgaskets. The heads will need to be decked/resurfaced by a machine shop. Use OEM gaskets or Felpro MLS head gaskets. Since you are in there you could slap in some ARP headbolts for extra insurance. I would also replace the timing belt component kit as its due if the service intervals of 105k were followed. Replace the water pump as well with a new OEM thermostat. At this point this will make sure all of the internal cooling components of the engine are in good working order. Before you tackle the headgaskets I would hookup the heater core and see why that was bypassed in the first place. If it was the because the heater core leaks, since you're in South Florida you could bypass it with a looped hose to continue coolant flow for the engine. Or you could just make sure the engine side does have the coolant lines looped so that the coolant flow for the engine isn't just blocked off. Those coolant lines are by the starter/steering column connection point inside the engine bay.
-
Removing '05 GT Camshaft Position Sensor P0340
Berge56 replied to jmcgliss's topic in Fourth Generation Legacy (2005 - 2009)
Glad to hear the OCV's worked! -
Mystery spring clip is loose
Berge56 replied to Jolbaru_LGT's topic in Fourth Generation Legacy (2005 - 2009)
That is a coolant line that runs from your water pump to your heater core. That clip should be around the hose. Get a pair of long needle nose plyers, you should be able to reach down with them, squeeze the clip and get it back around the hose. -
FS (MA): 17x7.5 Verde saga 5x1114 40mm offset *
Berge56 replied to Berge56's topic in Member Classified (2015 - )
Monday Bump -
FS (MA): 17x7.5 Verde saga 5x1114 40mm offset *
Berge56 replied to Berge56's topic in Member Classified (2015 - )
PM'd you -
Up for sale is a set of Black Verde rims that have TPMS sensors already installed. Specs on the wheels are 17x7.5 with a 40mm offset and are 5x114. All 4 rims are in great condition, have no cracks, welds or bends and I no longer need them as the car was sold. New these rims were 900 and the tpms sensors were 300. Looking for 400 OBO. I would prefer local pickup, however rims are boxed up, so if buyer would like a quote on shipping I can do so but at an extra cost.
-
fs - location: Tomei Equal length headers
Berge56 replied to Berge56's topic in Member Classifieds (2005 - 2009)
Mods please close. Headers were sold -
Removing '05 GT Camshaft Position Sensor P0340
Berge56 replied to jmcgliss's topic in Fourth Generation Legacy (2005 - 2009)
I use this website as they have quick shipping and are only 1 state away. They also have great pricing. The OCV's are 100 and change on their website. https://www.subarupartsauthority.com/ I've seen these OCV's cause stupid issues and some people have had luck cleaning them. I've always had to replace them and it did solve hesitation and misfire issues for me. -
Stock fueling not enough for VF52
Berge56 replied to Pleides's topic in Fourth Generation Legacy (2005 - 2009)
my outback XT 5eat made almost the same exact power. I have a JMP 16G turbo with ID's 1050s amongst every other bolt on mod you can think of. Car drives great with the 1050's and was tuned for 19psi by Calvin @EFI. -
Removing '05 GT Camshaft Position Sensor P0340
Berge56 replied to jmcgliss's topic in Fourth Generation Legacy (2005 - 2009)
I would also try cleaning the oil control valve (OCV). That controls the cam shaft timing advance and can go bad. I had a hell of time with my outback XT and once I replaced both driver and passenger OCV and both cam shaft sensors all misfire codes went away. I only used used OEM parts as well. I hope this helps. -
Change the fluid with fresh 75-90 gear oil and see if the ATF tint comes back. If it does you could have a leak inside the transmission.
-
fs - location: Tomei Equal length headers
Berge56 replied to Berge56's topic in Member Classifieds (2005 - 2009)
Headers are sold! -
fs - location: Tomei Equal length headers
Berge56 posted a topic in Member Classifieds (2005 - 2009)
Up for sale is a set of equal length Tomei Headers with a 3 bolt uppipe. I am selling as I no longer need the headers and they have roughly 25k on them. All studs are in perfect shape and the factory EGT bung is properly plugged with a threaded bolt and crush washer. These headers brand new were $750 bucks and I am looking for 425 plus shipping. I'm located in Western Mass.