CBRRICH Posted June 8, 2023 Share Posted June 8, 2023 I have a 2005 legacy GT wagon MT. The ABS light has been intermittent for a few months and now it is on. I connected the "White Connector" in the fuse box and read: C0101 (Rear Right ABS Sensor Circuit Open or Shorted Battery) C0102 (Rear Left ABS Sensor Circuit Open or Shorted Battery) C0111 (Motor/motor relay on failure) It is unlikely all 3 are bad simultaneously, is there a way to clear the codes without buying a separate ABS capable reader so I can see if only one returns so I can just replace the one item causing the light to stay on? On Youtube there was an example of using a 6 pin connector and 2 separate pins inserting and removing the pin 3X in 10 sec to clear the codes but that was for 1993-2001 models. Is there a similar procedure for the 2005 model? Link to comment Share on other sites More sharing options...
Max Capacity Posted June 8, 2023 Share Posted June 8, 2023 You can reset the ECU by disconnecting the battery for 15 minutes. After you reconnect the battery, turn the Key to ON for 10 seconds before starting. I think that should clear the codes. Drive the car about 60 miles for the CEL to return. Some of the big Auto Parts stores will read and clear codes for free. Like Auto Zone and Advance auto parts It also has been found the rear ABS sensors tend to get worn on an angle. 305,600miles 5/2012 ej257 short block, 8/2011 installed VF52 turbo, @20.8psi, 280whp, 300ftlbs. (SOLD). CHECK your oil, these cars use it. Engine Build - Click Here Link to comment Share on other sites More sharing options...
CBRRICH Posted June 9, 2023 Author Share Posted June 9, 2023 Thanks for the suggestion. I tried it, it did not reset the ABS codes, all (3) appeared again. Maybe it only works for CEL reset? Autozone here in Massachusetts will not reset any codes and they said they could not read ABS codes but then I have found I often get a different story from different stores. They all, however, said they would not reset codes. Any other ideas on how to erase the codes w/o a reader? I was thinking maybe there is a sequence of pressing the odometer button since that is how you get the codes to read in the first place. Link to comment Share on other sites More sharing options...
silverton Posted June 10, 2023 Share Posted June 10, 2023 (edited) On 6/7/2023 at 7:37 PM, CBRRICH said: I have a 2005 legacy GT wagon MT. The ABS light has been intermittent for a few months and now it is on. I connected the "White Connector" in the fuse box and read: C0101 (Rear Right ABS Sensor Circuit Open or Shorted Battery) C0102 (Rear Left ABS Sensor Circuit Open or Shorted Battery) C0111 (Motor/motor relay on failure) It is unlikely all 3 are bad simultaneously, is there a way to clear the codes without buying a separate ABS capable reader so I can see if only one returns so I can just replace the one item causing the light to stay on? Most places that check for codes only have basic OBD readers that will only read/clear engine codes. AFAIK they won't clear codes as there is some liability thing about safety inspections and whatnot. But if it's been intermittent for a few months, and when you finally decided to check it's three things, how do you know that all three went bad at the same time? Just food for thought With those three codes showing, I'd follow the diagnostics tree for C0111 first, both rear sensors share a joint connector from the ABSCM (the abs pump in the engine bay). Wiring diagram for the speed sensors Edited June 10, 2023 by silverton 1 Link to comment Share on other sites More sharing options...
CBRRICH Posted June 10, 2023 Author Share Posted June 10, 2023 Thanks, I'll give it a try. Link to comment Share on other sites More sharing options...
KZJonny Posted June 10, 2023 Share Posted June 10, 2023 Chasing down something similar. Pretty sure it is a bad wheel speed sensor, but if not, thanks for the diagnostic tree post up. Link to comment Share on other sites More sharing options...
Cegueta Posted June 11, 2023 Share Posted June 11, 2023 On 6/8/2023 at 11:09 AM, Max Capacity said: You can reset the ECU by disconnecting the battery for 15 minutes. After you reconnect the battery, turn the Key to ON for 10 seconds before starting. I think that should clear the codes. Drive the car about 60 miles for the CEL to return. Some of the big Auto Parts stores will read and clear codes for free. Like Auto Zone and Advance auto parts It also has been found the rear ABS sensors tend to get worn on an angle. I just changed mine. Looks identical with the angle. BTW I have the same issue, I cannot erase the codes on my legacy. Link to comment Share on other sites More sharing options...
KZJonny Posted June 11, 2023 Share Posted June 11, 2023 Well, followed the C0111 diagnotic tree and everything checks out. Good voltage and ~0.02 ohms where there ought to be 0-0.5. Trying a battery disconnect code clear to see if that deleted stores codes. If not, on the next diagnostic tree and maybe see if they clear with some time behind the wheel? Link to comment Share on other sites More sharing options...
KZJonny Posted June 13, 2023 Share Posted June 13, 2023 So, for anyone else following along, I did the C0111 diagnostic tree, and everything is coming up sunshine. The harness is getting power, and the grounds are fine. Next steps are the diagnostic trees for C0105 and C0109, which are for no or low voltage to the sensors... Since the sensors are new or newish, or at least, worked fine before I swapped to the Spec B rear end (same axles as before), I'm thinking either I am not getting voltage/signal to the harness side connector(s). Ordered some longer alligator clips for my DVOM and will see if I have any pins small enough to connect to the tiny wheel speed sensor connections. I really don't particulalry enjoy pinning anc back pinning stuff to find faults, but I also recognize that if I want to keep my old junk running, it's something I should probably get better at. Maybe start looking around for an affordable ocscilloscope. If there is anything wrong between the ABSCM and the harness at the wheel, perhaps harness B98 is the culprit. Anyone happen to know where that is? Finger crossed it is something simple, like bad ground at the end of the harness and I just need to clean and repin/replace. We shall see. Link to comment Share on other sites More sharing options...
Infosecdad Posted June 14, 2023 Share Posted June 14, 2023 I have one of the Pokit Pros and it's really nice. https://www.pokitinnovations.com/ Link to comment Share on other sites More sharing options...
KZJonny Posted June 14, 2023 Share Posted June 14, 2023 12 hours ago, Infosecdad said: I have one of the Pokit Pros and it's really nice. https://www.pokitinnovations.com/ Damn, that is a cool looking toy. I'm still not on the smartphone + data plan train tho. So, I need everything I buy to be standalone capable. Link to comment Share on other sites More sharing options...
CBRRICH Posted June 14, 2023 Author Share Posted June 14, 2023 Have not found a way to clear ABS codes so I ordered a OBDII reader on Amazon that can read/erase ABS codes for ~$45 used. Hopefully after clearing the codes, one of the 3 will reappear. Link to comment Share on other sites More sharing options...
CBRRICH Posted November 21, 2023 Author Share Posted November 21, 2023 No luck, I have ordered (2) different OBD/ABS tools both of which could not read (nor clear) my 2005 (Innova 3020RS and 5110). To recap, I was successful in reading the codes using the jumper but need to clear them to be sure I am troubleshooting the right code (3 codes are currently showing). Anyone used any other scanners they can recommend that successfully read and cleared the ABS codes for a 2005 GT? Link to comment Share on other sites More sharing options...
Max Capacity Posted November 21, 2023 Share Posted November 21, 2023 Just asking, have you replaced both rear sensors ? Or at least pulled them out to inspect them ? They are easy to replace, NAPA has them. 305,600miles 5/2012 ej257 short block, 8/2011 installed VF52 turbo, @20.8psi, 280whp, 300ftlbs. (SOLD). CHECK your oil, these cars use it. Engine Build - Click Here Link to comment Share on other sites More sharing options...
CBRRICH Posted November 21, 2023 Author Share Posted November 21, 2023 I have replaced LR in 2014, again in 2021 and the RR IN 2017 , they were ~$70 each so I want to be sure which one is the problem before just replacing parts until I find the bad one. It is unlikely both went bad at the same time. Also the module has a code as well. That is why I would like to clear the ABS codes and see which one(s) return. How do you check the sensors? Link to comment Share on other sites More sharing options...
Max Capacity Posted November 21, 2023 Share Posted November 21, 2023 I would think you'd need to check them for continuity, but I'm no expert. You may want to PM "m sprank" 305,600miles 5/2012 ej257 short block, 8/2011 installed VF52 turbo, @20.8psi, 280whp, 300ftlbs. (SOLD). CHECK your oil, these cars use it. Engine Build - Click Here Link to comment Share on other sites More sharing options...
Max Capacity Posted November 21, 2023 Share Posted November 21, 2023 I sent him a PM with this thread. 305,600miles 5/2012 ej257 short block, 8/2011 installed VF52 turbo, @20.8psi, 280whp, 300ftlbs. (SOLD). CHECK your oil, these cars use it. Engine Build - Click Here Link to comment Share on other sites More sharing options...
m sprank Posted November 21, 2023 Share Posted November 21, 2023 (edited) Could be the bearing, could be the sensor, could be the half shaft, could be.... a 20+ year old car showing its age. Wiring, contacts, degradation. Not going to find a "retail" scanner that clears ABS codes. Those are intended to auto-reset when the problem is fixed. Even a commercial scanner that can clear them cant keep them from coming back moments after starting/driving the car if the error persists. IIrc the regulations were written in the 90's. Clearing them is not the easy troubleshooting solution you wish it to be. Ask me why I prefer carburetor fuel system engines, cable driven throttles and mechanical brakes? When a salesman asks if I want the tech package, I ask if they have a Full Retard package. Like Ben Stiller in Tropic Thunder. Edited November 21, 2023 by m sprank 1 Link to comment Share on other sites More sharing options...
KZJonny Posted November 22, 2023 Share Posted November 22, 2023 6 hours ago, CBRRICH said: I have replaced LR in 2014, again in 2021 and the RR IN 2017 , they were ~$70 each so I want to be sure which one is the problem before just replacing parts until I find the bad one. It is unlikely both went bad at the same time. Also the module has a code as well. That is why I would like to clear the ABS codes and see which one(s) return. How do you check the sensors? Don't have the link handy, but download the 'vacation pix' for your year/model. There is a pretty comprehensive rundown of how to diagnose the ABS module and also your wheel speed sensors. This plus whatever code scanner you have or just the dashboard C-code display is pretty helpful. All you need is a DVOM and maybe some extended length leads. Helped me to track down a bad wheel speed sensor and explain the "SS" code I have in my odometer. Now I just need to fix said problem. Link to comment Share on other sites More sharing options...
Max Capacity Posted November 22, 2023 Share Posted November 22, 2023 Index of /ilh/vacation There's the service manuals. I have that link saved in my Bookmarks, as everyone should. I also have the manual downloaded into my documents. 305,600miles 5/2012 ej257 short block, 8/2011 installed VF52 turbo, @20.8psi, 280whp, 300ftlbs. (SOLD). CHECK your oil, these cars use it. Engine Build - Click Here Link to comment Share on other sites More sharing options...
KZJonny Posted November 22, 2023 Share Posted November 22, 2023 2 hours ago, Max Capacity said: I have that link saved in my Bookmarks, as everyone should Oh Snap! Link to comment Share on other sites More sharing options...
Max Capacity Posted November 22, 2023 Share Posted November 22, 2023 1 minute ago, KZJonny said: Oh Snap! Oh, you young guy's... I've been saving things in my favorites/bookmarks for many decades. I still have a bunch of things saved about these cars. 305,600miles 5/2012 ej257 short block, 8/2011 installed VF52 turbo, @20.8psi, 280whp, 300ftlbs. (SOLD). CHECK your oil, these cars use it. Engine Build - Click Here Link to comment Share on other sites More sharing options...
m sprank Posted November 23, 2023 Share Posted November 23, 2023 (edited) 8 hours ago, Max Capacity said: Oh, you young guy's... I've been saving things in my favorites/bookmarks for many decades. I still have a bunch of things saved about these cars. I have a bunch of dead links that even the way back machine cant find. More importantly did you check out the ECM 2024 thread? NY this year. Are you available/able to attend??? Edited November 23, 2023 by m sprank 1 Link to comment Share on other sites More sharing options...
Tehnation Posted November 23, 2023 Share Posted November 23, 2023 The C0111 code is probably whats causing the real issue. Did you change the relay? Link to comment Share on other sites More sharing options...
CBRRICH Posted November 25, 2023 Author Share Posted November 25, 2023 Thanks for all your help. First point: Since these codes are supposed to be "self clearing", If I read them with jumper in the fuse box I should assume that none are "Historic" and have been created the last time I drove it? Second point: I just rebuilt the entire rear end replacing all 14 bushings, rusted brake backing plates, struts/shocks, and new rear wheel bearing from SKF. However, the ABS light was on throwing these 3 codes before I started so I don't think the bearings are an issue, others have used SKF bearings without issues: C0101 (Rear Right ABS Sensor Circuit Open or Shorted Battery) C0102 (Rear Left ABS Sensor Circuit Open or Shorted Battery) C0111 (Motor/motor relay on failure) The lead up was the ABS would come on intermittently, sometimes I could turn the key off and on while moving and it would reset for 20 minutes then come on again. Now it occasionally goes out but only for short periods. Also the diagnostics for C0101/2 (ABS(diag)-40) require an oscilloscope (step 6) and clearing the memory (step 7) but I can try the other steps but it usually is the sensors that go. One other thing I noticed from the wiring diagram is that the rear sensors have a common connector (ABS (diag)-38), not sure where to find it on the car? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now