JMLegacy

My experience with the ignition retard is that it causes clutches to slip. It's almost like not lifting off the gas pedal when shifting gears in a manual. Do not modify that table without modifying the calculated torque and other necessary torque tables or at best a HEXAGRAM valve body mod.

What a coincidence, happened to me this morning!

Yes. The first time i touched it i noticed it kinda lurches me a little more. But in a way that makes me think it is promoting slipping. Kinda like not coming off the clutch fully in a manual before hitting the accelerator again. THe Calc TQ tables fixed that a somewhat, now i feel more comfortable having the power on earlier (from less retard) as now it spends less time shifting (with the CAlC tq adjusted) I'm not sure if it's mind over matter, but thats what i felt.

Slightly to 7400. Stock is 7000. NOt USDM which around 6K or 6.5

UTC_Pyro and Throttle_Happy, before and after: [ame=http://www.youtube.com/watch?v=Hu28s-JiFTM]Before: RT and timing on shift only[/ame] [ame=http://www.youtube.com/watch?v=ope5gRx6rWU]After: Calculated TQ & Requested torque + Timing on shift[/ame] Much faster shifts now thanks. I recon first one shifted within 76ms, the second one with Calc TQ at 53ms (1st to 2nd gear) though the first one had a slighty faster 0 - 100 time as it was a night time run and smoother road surface

Yes, I've been looking for that. Most of the tables in this rom seem to use the B tables over the A, at least when i'm in manu-shift mode. But based on how these values are, i'd say A table is used. Throttle_Happy please chime in

I've been using my RL based cable to flash cars for many years. I flash with version 1.29 ecuflash, and i edit with romraider. If you want to edit with the latest version of ecuflash, Install xp mode and edit inside that, and then copy file over to flash with 1.29

Note that the gen 4 JDM legacys all use the Spec B stiffer LCA bushing. JDM tophats are firmer than USDM JDM bushings are also firmer it seems Not just in subaru but in other vehicles (honda civic) I remember ordering a US tophat for my civic because it was "Cheaper" took a week and had to get the JDM one, was too squishy! vehicles that use the STI bushing: http://opposedforces.com/parts/info/20204AG011/

Best I could do. The noise you hear is my steering column touching my downpipe from the engine twisting as it launches. [ame=http://www.youtube.com/watch?v=38-ztXfHjRM]20160419 220143 0 - YouTube[/ame] Old tranny that was damaged that we talked about. No idea as yet what the new one i put in yesterday will do. I'm convinced the extremely low fluid caused its death. If you are referring to my video it's self tuned. VF 34, Water meth, 2.0 liter. Singapore model, I have a lot more i can pump out,.. but the rods are stock and thin like ej205 edit... Now that I'm looking on the video it's actually quite fast shifting for stock. I hope that VB wasn't modified! That map was running 400 RT values.

Can you confirm that the drill bits are for the different Shift aggressiveness levels? I was reading something to that effect on a Nissan board but i can't find it back. Something about "Hot rod" setting

I wonder how much faster this will change gears when I get a hexmods. It's already quick-ish [ame=http://www.youtube.com/watch?v=BUNKO4eJI5c]Drag 14.1 seconds - YouTube[/ame] JDM

[ame=http://www.youtube.com/watch?v=WdfDz86KAX8]Vibrant Ultra quiet resonator, 3" Catless dp, half Hogzaust mod - YouTube[/ame] 2004 JDM LGT with UEL headers VF34 3" downpipe 2.5 stock catback's resonator replaced with vibrant ultra quiet resonator

How does it idle? Disconnect your maf sensor and drive. If it behaves OK then check for boost and vac leaks +1 in BPV failing

Do u have a lazy third gear during lockup? What causes this? https://www.youtube.com/watch?v=9RHqAtZuM5Q check my video out for reference. When it reaches third, it slows right down. It even shows on the road dyno a huge dip in the lockup region. I get higher numbers in 2nd gear

Alright, slow down. If you are only logging you do NOT need to go in ECU flash. In romraider, did the COM port become selectable in the dropdown at the top?

There is a great void for a JDM LGT intercooler fitment. I can be your test fitter.

I add a 0.01uf cap to pins 5 and 7. Still cutting out, but not as frequent added a 0.1uf cap intead. Now the cable is unable to flash

Ok they say put a cap bridge across pins 5 and 7. Would it be easier to do this to the cable instead of the connection on the car? I'm not sure if i can access behind the connector http://www.ls1tech.com/forums/attachments/conversions-hybrids/30711-who-has-modified-their-own-ls1-harness-obd-ii_pinout.jpg

When in 2nd or 3rd gear I have difficulty loggin anything above 4500RPM. Romraider just cuts out. I even removed all but 4 parameters logged and same behavior. Some folks say It's interference. Some say ECU is busy. I have no idea whats happening here as it never really used to happen!

Is this the same process for the jdm bl5?

[ame=http://www.youtube.com/watch?v=rLdDl5deOyg]06' Legacy GT Megan Exhaust Vibrant Resonator Before and After - YouTube[/ame] One of the best sounding videos I could find on Youtube. The uploader ran through several setups but check the last 4 seconds of the video

The turbo sits closer to the usdm the the jdm

The JDM and USDM intercoolers are not interchangeable USDM http://i.ebayimg.com/t/Subaru-Top-Mount-Intercooler-08-Impreza-WRX-04-08-Legacy-GT-OEM-/00/s/OTAwWDEyMDA=/z/g-wAAOxyY3ZR3KkP/$T2eC16h,!)QE9s3HG-uEBR3KkPKS3Q~~60_57.JPG JDM http://i.ebayimg.com/t/JDM-Subaru-03-09-Legacy-BP5-BL5-EJ20-Turbo-OEM-Intercooler-w-Blow-Off-Valve-BOV-/00/s/NDgwWDY0MA==/z/qnIAAMXQxVZRD1uO/$(KGrHqV,!g8FDfHnT,ziBRD1uN7Ny!~~60_3.JPG

Hey guys, I'm replacing the bend on my intercooler (JDM style bend) It's the hose that leave the turbo and 90* bend to the intercooler. http://legacygt.com/forums/attachment.php?attachmentid=106120&thumb=1&d=1319111805 I'm now in need of a flange that will mate up with the LGT style turbo I looked everywhere and cannot find a part like that. Does anyone know anybody that makes this?

I agree with you. But based on my estimation it won't change much. Looking at my spoolup region in my tables it can't get much leaner than that, and dual AVCS...maybe AVCS can take some more pressure. Idk though, leave that to the tuner