cantona156 Posted March 14, 2006 Share Posted March 14, 2006 Hello I seem to have busted my front lower arm rear bushing (what a mouthful). Does anyone know the part number? Are there any polyurethane replacement for it (like PowerFlex)? Thanks. Link to comment Share on other sites More sharing options...
Xenonk Posted March 15, 2006 Share Posted March 15, 2006 ???? how can anyone break one in the first place?? got a pic? maybe call up Energy Suspension and see if they have a similar part that you can substitute it for? Keefe Link to comment Share on other sites More sharing options...
RobY Posted March 15, 2006 Share Posted March 15, 2006 Perrin makes a Pilloball "bushing" solid steel and aluminum. Link to comment Share on other sites More sharing options...
cantona156 Posted March 15, 2006 Author Share Posted March 15, 2006 According to the service manual, it can be replaced. But didn't say anything about the part number! http://img112.imageshack.us/img112/9598/img0099copy1fc.jpg http://img112.imageshack.us/img112/9784/img0102copy4di.jpg Link to comment Share on other sites More sharing options...
SC GT Posted March 15, 2006 Share Posted March 15, 2006 Part No. 20204AG01A. Link to comment Share on other sites More sharing options...
ebpda9 Posted March 15, 2006 Share Posted March 15, 2006 shouldn't it be under warranty ? and by the way my car handles i suspect the one on the passanger side is a goner on my car too. i just did not have a chance to replace it. energy suspension sells them by the size too. just get a caliper and measure it. chancees are they will make one. Link to comment Share on other sites More sharing options...
bluechipbmw Posted March 15, 2006 Share Posted March 15, 2006 what causes this to happen? and what should I expect to notice when this does happen? Link to comment Share on other sites More sharing options...
Wangspeed Posted March 15, 2006 Share Posted March 15, 2006 I'm not sure a spherical bearing in that location would be very good. Are we sure that it doesn't require 3 axis movement? The rubber would allow that, but the spherical bearing setup from Perrin probably does not. Plus spherical bearings that are not closed are usually a bad idea on the street. Teflon lined or not. They should be sealed like the sti parts, or the Evo control arms. Warren Link to comment Share on other sites More sharing options...
GTsleeper Posted March 15, 2006 Share Posted March 15, 2006 holey shot how did that happen already. it could be from the a/c drain right their. isnt there a sti upgrade bushings? the bearing set-up..... that bushing only needs to travel up/down with the suspention travel. less side to side flex= better. but im sure comfort will change slightly. Link to comment Share on other sites More sharing options...
Deer Killer Posted March 15, 2006 Share Posted March 15, 2006 It's rubber. it wears. it tears. Link to comment Share on other sites More sharing options...
cantona156 Posted March 16, 2006 Author Share Posted March 16, 2006 Well, if you have uprated sway bars, take hard corners, run over rough roads (near off roads kind), pls have your bushing checked. Link to comment Share on other sites More sharing options...
cantona156 Posted March 16, 2006 Author Share Posted March 16, 2006 Part No. 20204AG01A. Hi Thanks. Wonder where did you find this part number? Link to comment Share on other sites More sharing options...
Wangspeed Posted March 16, 2006 Share Posted March 16, 2006 I wonder if the bushing in the Spec B aluminum control arms is the same, or if it's better. Warren Link to comment Share on other sites More sharing options...
SC GT Posted March 16, 2006 Share Posted March 16, 2006 Hi Thanks. Wonder where did you find this part number? Vacation pix. Link to comment Share on other sites More sharing options...
edmundu Posted March 20, 2006 Share Posted March 20, 2006 So how entailed is this to replace? Big job, small job? DIY'er friendly, or a shop job only? I think I have the same exact thing on both my front arms. Trouble is, I'm out of warranty, but I could swear I saw them looking like that from almost day one? I never gace it much thought. They only cost like $7.34 ea, but I'm curious on the amount of labor involved... Link to comment Share on other sites More sharing options...
cantona156 Posted March 21, 2006 Author Share Posted March 21, 2006 So how entailed is this to replace? Big job, small job? DIY'er friendly, or a shop job only? I think I have the same exact thing on both my front arms. Trouble is, I'm out of warranty, but I could swear I saw them looking like that from almost day one? I never gace it much thought. They only cost like $7.34 ea, but I'm curious on the amount of labor involved... From the service manual, it seems that you require some machine to press the bushing in. I can email you the document if you can pm me your email. Link to comment Share on other sites More sharing options...
ebpda9 Posted March 21, 2006 Share Posted March 21, 2006 your local autozonewould loan you their balljoints replacement set to do it. all you need is an impact wrench and some compressed air. Link to comment Share on other sites More sharing options...
edmundu Posted March 21, 2006 Share Posted March 21, 2006 I thought the bushing was pressed in? No hydraulic press needed? Link to comment Share on other sites More sharing options...
Rommel Posted March 21, 2006 Share Posted March 21, 2006 the bushings are pressed in Link to comment Share on other sites More sharing options...
Deer Killer Posted March 21, 2006 Share Posted March 21, 2006 It takes a few seconds with a hydraulic press, otherwise hours, plenty of swearing, and possibly never. Link to comment Share on other sites More sharing options...
Leonardo Posted March 21, 2006 Share Posted March 21, 2006 Local guy here has that problem on his GT but he auto-x's the damn thing. Someone sould make that in a harder material but not solid. Spec B part# the same? Link to comment Share on other sites More sharing options...
cantona156 Posted April 18, 2006 Author Share Posted April 18, 2006 Does anyone knows of a polyurethane replacement for this part? Thanks. Link to comment Share on other sites More sharing options...
CombatCQB Posted June 22, 2006 Share Posted June 22, 2006 Anyone here done the bushing change yet? I've seen some joint pullers are really just some C-clamps. So I'm planning to try using a benchtop vice and some right diameter piping as adapters. Link to comment Share on other sites More sharing options...
Xenonk Posted June 22, 2006 Share Posted June 22, 2006 I wonder if the bushing in the Spec B aluminum control arms is the same, or if it's better. Warren I had a talk with some of the other guys looking into that, and it seems to be the same rubber bushing, only difference is that the arm is aluminum and not steel.. As regards to your Perrin PSRS kit, yea, I am very sure it's just a 2-axis system.. best thing to do is just order some poly bushings instead and just get them pressed in to retain the 3-axis movement.. I am pretty sure Perrin claimed that their kit eliminates one of the axis to "give a better feedback" and also increases caster (as their bushings have markings for alignment?). I think there's already 1 or 2 people that already did the Perrin PSRS kit on their cars.. I forgot who, but SEARCH is your friend. Keefe Link to comment Share on other sites More sharing options...
chuckzul Posted June 22, 2006 Share Posted June 22, 2006 Does anyone knows of a polyurethane replacement for this part? Thanks. AFAIK, there is no poly replacement bushings, but as Keefe mentioned, there are a couple of people on here already running the Perrin spherical bushings with good results (albeit a little rougher). Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.