yamie700 Posted December 30, 2005 Share Posted December 30, 2005 Well I finally got around to installing my oil pressure gauge sender. I have had the gauge wired up with my boost gauge for a while but I was waiting on a few parts for the sender. Anyway, here is what I did to install the sender. First- take off the engine cover by removing the four pop-its.http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Enginecoverremoved.jpg Now you can see the empty oil galley, between the intercooler and the intake, it just has an allen plug in it. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Allenplugunderintercooler.jpg Remove the intercooler to get more access to the area, Take off the two bolts on the turbo. These are both 12mm. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Leftsideintercoolerbolts.jpg Then there is one 12mm bolt on the support bracket and two 10mm bolts for the recirc valve. Then loosen the hose clamp that attaches the intake (no picture of that) and you can remove the intercooler. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Rightsideintercoolerbolts.jpg Here is a side shot with the intercooler removed, I wadded up a thick paper towel and blocked the turbo just in case. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Intercoolerremoved.jpg Link to comment Share on other sites More sharing options...
yamie700 Posted December 30, 2005 Author Share Posted December 30, 2005 Now you can remove that allen plug. I used an L 5/16" allen wrench, putting the long end of the L into the plug as there isn't room the other way. I then used a 10mm deep socket with an extension to get some leverage on the wrench. The plug is really in there good, they must have used some kind of loctite at the factory. I wish I would have had a set of allen sockets as they would have made the job much easier. I'm sure the true size of the plug is metric but the 5/16 did work for me. Here is the oil galley with the plug removed. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Allenplugremoved.jpg I bought the subaru part below, $8.xx, to put in the allen plugs place. You will also need to get the washer/gasket that goes with it, part #037018200. This part is threaded 1/8 bspt so if you have an npt threaded sender, like I do, you will need to get a bspt to npt adapter. There are some places though that you can get this part threaded npt, www.wrxtra.com I believe is one. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Plugmaingalleywithbag.jpg Here is the plug main galley installed. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Plugmaingalleyinstalled.jpg Now, if your sender is small enough and threaded 1/8 bspt (like the defi ones I think) you could just screw it in and be set. A crows foot wrech would pretty much be a must in order to tighten it though. The sender that I have however, is tool large to fit here, so I had to remote mount it. Neil from VEI was very helpful in getting me the parts necessary to do this. Here is the SS hose connected to the plug via a bspt to npt adapter. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/SShoseinstalled.jpg And here is a shot of the sender installed. I just mounted it using an existing bolt for a hose support bracket. The hose looks close to the heat shield in the picture but I moved it a little before I was done. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Senderinstalledsideview.jpg You can see that I already connected the one wire to the sender required for the gauge. This is just a shot of the grommet I used to get my vacuum line and oil pressure wire through the firewall. These come in behind the HVAC blower, removing the glovebox is the easiest way to get at them. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Grommetwithlinesinstalled.jpg Now you just reinstall the intercooler. I do suggest putting a little vaseline or something slippery on the opening that connects the intercooler to the intake, otherwise it is a b*$%h to get them to slide together all the way. Also be careful when bolting the intercooler to the turbo as the bolts go in kind of at an angle and seem to cross thread easily. Link to comment Share on other sites More sharing options...
yamie700 Posted December 30, 2005 Author Share Posted December 30, 2005 And here are some shots of my gauges from VEI all hooked up. I am very happy with them and would recommend them to anyone. Neil from VEI was very helpful in setting up the group buy and answering questions right here on the forum, a big plus. http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Gaugeswflashboth0.jpg http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Gaugesonwflash.jpg http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Gaugesonlightsonnoflash.jpg http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Gaugescloseuplightson.jpg Link to comment Share on other sites More sharing options...
wukilla98 Posted December 30, 2005 Share Posted December 30, 2005 Looks good...nice job on the walkthrough. Link to comment Share on other sites More sharing options...
BLACKeNeD Posted December 31, 2005 Share Posted December 31, 2005 Thanks for the walk through...They look great. Hopefully, I will get a chance to get some gauges in after I get my mods up... Link to comment Share on other sites More sharing options...
Sub_Free Posted January 3, 2006 Share Posted January 3, 2006 Thanks for the write up! I have a few questions: 1. Did you use teflon tape on the oil galley adapter? 2. Is that a brass fitting? 3. What did you torque it down to? I just ordered my adapter and can't wait to get them installed. Link to comment Share on other sites More sharing options...
yamie700 Posted January 3, 2006 Author Share Posted January 3, 2006 1. I used teflon tape on all the threads for each connection. The subaru part actually came with a thread lock sealant already applied, however I installed it first and found out the sender was too big to fit so I had to take it out and put back the allen plug for a while. If I had all the SS hose at first I would not have needed teflon tape on that part. 2. Subaru part is not brass, all of the others are though. 3. I don't have a torque wrench so... I just went by feel, being careful not to overtighten the brass parts. It has been a couple days of driving now and I don't see any leaks. Link to comment Share on other sites More sharing options...
jagcars26 Posted January 4, 2006 Share Posted January 4, 2006 Great pics and walkthrough,,I've got the guages just need to install them. Rudy Link to comment Share on other sites More sharing options...
scans007 Posted January 5, 2006 Share Posted January 5, 2006 Wow that's killer man......I gotta get an oil gauge.... Link to comment Share on other sites More sharing options...
tsyGT Posted January 6, 2006 Share Posted January 6, 2006 Nice. Thanks for the pics and writeup. You need some gas though. tom Link to comment Share on other sites More sharing options...
jsalicru Posted March 7, 2006 Share Posted March 7, 2006 Here's a walk-through I made of a STi install. The Oil pressure is similar also. http://homepage.mac.com/jsalicru/GaugesHowTo.html "some say, his arms are made of coiled adamantium fibers. And that he tops his cereal with nuts and bolts. All we know is, he's called the Jose." Link to comment Share on other sites More sharing options...
TSiWRX Posted March 14, 2006 Share Posted March 14, 2006 Question to all - Is it necessary to drain oil from the engine before proceeding with the galley installation? Thanks! <-- I love Winky, my "periwinkle" (ABP) LGT! - Allen / Usual Suspect "DumboRAT" / One of the Three Stooges '16 Outback, '16 WRX, 7th Subaru Family Link to comment Share on other sites More sharing options...
yamie700 Posted March 14, 2006 Author Share Posted March 14, 2006 Nope, the galley is at the top of the engine and there is no pressure so it won't come flying out or anything. (Well if you had the engine on I guess it would:icon_wink ) Link to comment Share on other sites More sharing options...
TSiWRX Posted March 14, 2006 Share Posted March 14, 2006 ^ - Like my wifey likes to say: "OK, what did you break in the car THIS time?" Thanks, and thanks for the walk-through! <-- I love Winky, my "periwinkle" (ABP) LGT! - Allen / Usual Suspect "DumboRAT" / One of the Three Stooges '16 Outback, '16 WRX, 7th Subaru Family Link to comment Share on other sites More sharing options...
TSiWRX Posted March 20, 2006 Share Posted March 20, 2006 Again, bruddah, thanks for the walk-through - it's an AWESOME step-by-step, including what needs to be purchased! I truly appreciate your hard work in documenting this process and making it so easy. Question - what pressures are you seeing at both cruise and idle? ------------------------------------------ I got my AutoMeter NEXUS oil-pressure gauge hooked-up this weekend thanks to your excellent walk-through - and here's what little I can contribute to this thread ---> (1) The oil pressure sender relocation/extension/adaptor kit (for 1/8 NPT senders, like all AutoMeter units) from WRXtra: http://www.wrxtra.com/cat_3.html actually contains its own block galley plug/adaptor. However, to utilize it, you'll need to have a 15/16th socket, as it's one huge mother! (2) While the part provided with the WRXtra kit threads easily to the relocation/extension hose, I found it much harder to get to thread to our block than the Subaru OEM galley plug/adaptor; however, at the same time, it was also harder to thread the relocation/extension hose to the Subaru OEM component than with the one supplied by WRXtra - choose your poison. If you decide to "cross-mate" the Subaru OEM galley plug with the WRXtra extension hose, be sure to use some thread-sealant, as the female thread "inside" the Subaru OEM galley plug is not coated with thread sealant, nor is the male thread on the hose (WRXtra coats the "inside" female threads of its block galley adaptor). (3) Don't be like me, thinking that a crow's foot wrench isn't a necessity. Trust me, it definitely is. Go and get yourself at least the proper 7/16th crow's foot before you start this project. I actually had to stop for the night due to my disregard of this tool advice, only to need to start-up the next day, after having hopped down to Sears in my wifey's WRX. <-- I love Winky, my "periwinkle" (ABP) LGT! - Allen / Usual Suspect "DumboRAT" / One of the Three Stooges '16 Outback, '16 WRX, 7th Subaru Family Link to comment Share on other sites More sharing options...
yamie700 Posted March 20, 2006 Author Share Posted March 20, 2006 Again, bruddah, thanks for the walk-through - it's an AWESOME step-by-step, including what needs to be purchased! I truly appreciate your hard work in documenting this process and making it so easy. Question - what pressures are you seeing at both cruise and idle? At idle when first started it is in the upper 90's. When warmed up idle psi is in the 30's if I remember right. Cruising when warmed up is in the low 80 psi range. Its nice to know when the oil is up to operating temp based on the pressure going down, then I know I can drive a little harder. Link to comment Share on other sites More sharing options...
TSiWRX Posted March 20, 2006 Share Posted March 20, 2006 ^ Cool beans. And I'll definitely +1 that temp/pressure sentiment, too! <-- I love Winky, my "periwinkle" (ABP) LGT! - Allen / Usual Suspect "DumboRAT" / One of the Three Stooges '16 Outback, '16 WRX, 7th Subaru Family Link to comment Share on other sites More sharing options...
Deer Killer Posted March 22, 2006 Share Posted March 22, 2006 I just ordered the PRO/mad dad gauges from ebay and I'm going to do this, however the http://www.wrxtra.com prices are nuts.. They want $25 for nut with a threaded hole??? err.. Well, let me see how big the sender unit is when I get them.. Shouldn't like NAPA or something carry something like this? Link to comment Share on other sites More sharing options...
TSiWRX Posted March 23, 2006 Share Posted March 23, 2006 DK - Yes, it's steep, but heck, for me, I was more concerned about the fact that it was a "one-stop shop" with headache-free reputation. Having Anna has totally changed my priorities, LOL! AutoMeter carries their own BSTP-to-NPT adaptor, if I remember correctly. And yes, most of the bigger automotive parts retail chains will have such an adaptor handy. Similarly, they'll also have the hose and hose fittings that you'd need to extend/remote-locate the sender assembly. <-- I love Winky, my "periwinkle" (ABP) LGT! - Allen / Usual Suspect "DumboRAT" / One of the Three Stooges '16 Outback, '16 WRX, 7th Subaru Family Link to comment Share on other sites More sharing options...
Pinky Posted April 15, 2006 Share Posted April 15, 2006 Where did you get those gauges from? I can't seem to find them anywhere. Link to comment Share on other sites More sharing options...
TSiWRX Posted April 15, 2006 Share Posted April 15, 2006 ^ yamie's gauges are by VEI: http://legacygt.com/forums/showthread.php?t=22003&highlight=vei <-- I love Winky, my "periwinkle" (ABP) LGT! - Allen / Usual Suspect "DumboRAT" / One of the Three Stooges '16 Outback, '16 WRX, 7th Subaru Family Link to comment Share on other sites More sharing options...
JK_Asian Posted April 16, 2006 Share Posted April 16, 2006 Dude you need to get some gas..LOL Link to comment Share on other sites More sharing options...
Joon525 Posted June 3, 2006 Share Posted June 3, 2006 Just some advice for anyone else trying this for the first time... http://i11.photobucket.com/albums/a153/yamie700/LegacyGTcom%20stuff/Oil%20pressure%20gauge%20install/Allenplugremoved.jpg That plug is really far down in there. It doesn't look like it so much in these pictures but trust me it is. It seems that a magnetic pick up tool would be a good thing to have as well since there's not a lot of room in there for a human hand. One last thing, see that black hose that comes down and goes into this black L shaped thing....that might not be in the same position on your own car. I'm in the middle of this install right now found that line to be directly in the way of the galley. I can rotate it counterclockwise but it's a slight pain. That plug takes an 8mm allen socket as well. Link to comment Share on other sites More sharing options...
Deer Killer Posted June 3, 2006 Share Posted June 3, 2006 Disconnect the line going to the tee.. makes it easier, there's nothing in it. Link to comment Share on other sites More sharing options...
Joon525 Posted June 3, 2006 Share Posted June 3, 2006 Disconnect the line going to the tee.. makes it easier, there's nothing in it. So that black flexible rubber hose that goes to the hardline/L shaped "T" is vaccuum eh? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.