mwiener2 Posted August 27, 2007 Share Posted August 27, 2007 I have engiunity and ecuExplorer. These are the parameters I need to log: RPM A/F Ratio A/F Trim Current A/F Trim Learned Relative Pressure Turbo Dynamics TPS WGDC Dynamic Advance Multiplier Dynamic Advance EGT Ignition Timing Knock Activity Calculated Load I can find most of those in either program,and some of them are not in either logger. What program has all of those parameters? Is there an update to one of the programs to add parameters? My Mods List (Updated 8/22/17) 2005 Outback FMT Running on Electrons Link to comment Share on other sites More sharing options...
NSFW Posted August 28, 2007 Share Posted August 28, 2007 EcuExplorer is no longer maintained so Enginuity is a much better bet. The Enginuity guys release new definitions fairly often: http://www.enginuity.org/viewtopic.php?t=360 http://www.enginuity.org/viewtopic.php?t=1642 It's possible the names in the logger definitions changed after the was made, so some of the names won't exactly match the list you're starting from. "Relative Pressure" is "Manifold Relative Pressure," for example (I guess that one's obvious but you get the idea). Which ones, specifically, can't you find in Enginuity? Do you want to check your engine's health in general, or are you working with a tuner who has asked for these parameters specifically? If the former, see http://www.enginuity.org/Documentation/EnginuityFAQ#toc64 for another list to consider, which should map very closely to the Enginuity logger's list of parameters. Link to comment Share on other sites More sharing options...
mwiener2 Posted August 28, 2007 Author Share Posted August 28, 2007 TPS = throttle valve opening angle I can figure out most of those I can't find Turbo Dynamics, Dynamic Advance, Dynamic Advance Multiplier My Mods List (Updated 8/22/17) 2005 Outback FMT Running on Electrons Link to comment Share on other sites More sharing options...
merchgod Posted August 28, 2007 Share Posted August 28, 2007 I am going to assume this is a pro-tuner who wants you to send him logs so that he can tweak your tune by mail? If so, download and install the latest Enginuity logger defs (updated separately from the application) and here's what you need to log: RPM = Engine Speed A/F Ratio = Air/Fuel Sensor #1 A/F Trim Current = Air/Fuel Correction #1 A/F Trim Learned = Air/Fuel Learning #1 Relative Pressure = Manifold Relative Pressure (Corrected) Turbo Dynamics = Turbo Dynamics Integral Cumulative*AND Tubo Dynamics Proportional* TPS =Throttle Plate Opening Angle (Direct)* WGDC = Primary Wastegate Duty Dynamic Advance Multiplier = IAM* Dynamic Advance = Knock Correction EGT = Exhaust Gas Temperature Ignition Timing = SAME Knock Activity = probably means Knock Signal #1 switch but that is retarded to log. Log Feedback Knock Correction* AND Fine Learning Knock Correction* instead Calculated Load = Engine Load* (don't log engine load % - units should be g/rev) Link to comment Share on other sites More sharing options...
mwiener2 Posted August 29, 2007 Author Share Posted August 29, 2007 ^^ Close. I'm helping COBB with some new product testing Thanks a bunch My Mods List (Updated 8/22/17) 2005 Outback FMT Running on Electrons Link to comment Share on other sites More sharing options...
enthusiast Posted August 29, 2007 Share Posted August 29, 2007 ^^ In a Outback! Just kidding. My mod list Link to comment Share on other sites More sharing options...
mwiener2 Posted August 29, 2007 Author Share Posted August 29, 2007 Yeah in an outback!!! gotta make sure it fits My Mods List (Updated 8/22/17) 2005 Outback FMT Running on Electrons Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.