Niko0422

Thank you all, I think I will try the Meguiar kit before anything . Saw some good result online. im also looking into the Red line goods steering wheel cover and it requires that I specify wether it is leather or plastic . I have the lowest trim of the 2.5i legacy 14 6mt , it looks like the wheel is plastic made to look like leather , can someone confirm this is correct ?

Did not buy yet, but I want to replace the clear cover of my headlights since they are pretty beat up and foggy. I saw these ones on Aliexpress for $64 for both. Has anyone purchased them before? I also saw a few on EBAY, but $86/ side. If someone could point me in the right direction I would appreciate it. Thanks https://www.aliexpress.us/item/3256803282863929.html?pdp_npi=2%40dis!USD!US %2444.88!%2435.90!!!!!%402103364716758843296343455e0e7d!12000025926089996!btf&_t=pvid%3Acd5330ab-9928-4a4f-80d8-f7b465310d0d&afTraceInfo=1005003469178681__pc__pcBridgePPC__xxxxxx__1675884329&spm=a2g0o.ppclist.product.mainProduct&gatewayAdapt=glo2usa&_randl_shipto=US

I replaced the burned bulbs for my license plate, back up light and tail light with Diode Dynamics leds, but shortly after driving my Vehicle Dynamic Control light and Brake Light turned on and stayed on. Has anyone else experienced this? They reset after I turn off the car but come back on after 5 minutes of driving

Wash and detailed her Sent from my iPhone using Tapatalk

Thank you very helpful! Would you be able to tell me where did you get the smoked corner lenses from? i have '14 legacy so some of the headlight is already black out and was planning on painting the rest of the chrome black as well, is it as simple as just spraying it with black paint? or does the chrome have to be sand?

Have not done yet, but I am thinking of adding some Halos. I remember seeing a thread on how to open and black out the headlights, but I can't seem to find it, I tried searching the forum through google, but not luck. Does any one have the link to the thread? thank you

Changed the mesh on the cmod grill for an abs plastic one and made a lower grill as well. Need to change the trim on the lower grill and figure out how to install it Sent from my iPhone using Tapatalk

I tried the cmod grill to see how it looks . Had a rough time getting the lower two clips into the bumper opening but finally got them in. The two screws at the bottom do not seem to reach the grill. Are we suppose to buy longer screws ? Any advice ? Sent from my iPhone using Tapatalk

Thank you, I did not receive the grille yet so im not too sure of what it includes, but are we able to use the push pins and the bumper holes used with the OEM grill?

Was finally able to purchase the C-mod grille for my car. Debating on whether I should install myself or pay the $200 for the shop to do it. Any advice on the installation?

Just an FYI for anyone also looking for the Cmod grille for the 13-14 part# SULE13MG. There’s a website called Rstorio offering it for CA$119 (US$96) . DO NOT BUY IT, it is a scam website looking to take your money and credit card info Sent from my iPhone using Tapatalk

I’m trying to buy the cmod grill for the 14 legacy but was unable to do it from their website , are they closed ? Sent from my iPhone using Tapatalk

Installed OEM interior light kit. Not sure how I feel about the mixture of blue and red lights . Has anyone tried changing the lights in the temperature control box ? Sent from my iPhone using Tapatalk

Didn't do it yet, but i am replacing the PCV valve this weekend. The manual says to use Three Bond 1324, is there another equivalent that can be used? Also, the manual calls for a liquid gasket, but from what i've read the Three Bond 1324 is more of a thread lock From what I read it is equivalent to loctite 243 , can anyone confirm? Thanks

I am interested in the skirts and the spats. Im in CT. Will they fit the 2014 legacy?

I removed the chrome window trim , sanded and painted black. I used a self etching primer from duplicolor and base coat from duplicoloe as well , but the paint rubs off too easily :/. I think it might be because it was too humid when i painted outside . I’m planning to repaint again this weekend. Has anyone else done this? Will an adhesion promoter before the self etching primer Help ?

I was wondering is there a way to change the red LEDs on the dash , starter ring and the climate control unit to blue? I searched the forum but could only find information on 2nd gen legacy. Has anyone done this on the 5th gen? Sent from my iPhone using Tapatalk

Thank you ! I shouldved asked before I started everything , all day wasted Sent from my iPhone using Tapatalk

I tried installing the Prothane inserts today , I had to cut one of the bolts on the front support and on the rear I wasn’t able to remove the nut on the right side because it rotates with the stud and I couldn’t find a wait to hold the stud still form the back since it seems to be inside the differential. I tried installing the insert on the one side I was able to remove but I don’t understand how it is suppose to squeeze in , there doesn’t seem to be any room for the insert legs to go in . Am I missing soemthing ? Any help is appreciated. I need to have the car running again by Monday for work , thanks in advanced ! Sent from my iPhone using Tapatalk

Installed the Subaru interior light kit today. Looks pretty weak , tried it inside the Garage because it was still daylight but doesn’t illuminate like I expected it too. Sent from my iPhone using Tapatalk

Thinking of removing the front grill and painting it black. Are the chrome wings and border removable ? Or will I just have to mask the whole grill ? Sent from my iPhone using Tapatalk

Detailed it myself for the first time ever during the weekend. Also, didn’t do it yet, but I’m planning on painting my calipers this Thursday. I can’t decide between black or blue , and just wanted some opinions I want to eventually change the wheels to black Sent from my iPhone using Tapatalk

I didn’t buy yet , but I had purchased some emblem overlays from emblemoverlays.com about 3 years ago. They never fit perfectly one side was always a little too short. Well the stars are starting to peel so I want to buy a new one. Any recommendations on where I can buy good overlays that will fit ?

Installed the front kart boy links today. I had bought the KB-017WLS Spacers thinking they were .5” but they were actually .25”. Had to use the .5” spacers that came with the rear links and 2 .25” spacers stacked together on each side to get the right thickness. The front feels great , torqued the links to 45 ft-lbs per Tom @ kartboy’s recommendation. The car vibrates a little when I make a left or right turn , will this go away with time ? Also, does anyone have the correct part number for .5” spacers? I will need them for the rear link installation and also will want to replace the .25” Stacked spacers I used in the front with one .5”