OGHK87Jay Posted November 30, 2011 Share Posted November 30, 2011 I need schematic on how to pull out the radio console, nav bezel, and the shifter area. Someone please post some pics or a pdf of how to do it please. I'm thinking to replace the radio and a my ring dropped out of the ash tray into the void area. Link to comment Share on other sites More sharing options...
Drift Motion Posted November 30, 2011 Share Posted November 30, 2011 - Take off wood trim, it's just tabs, pulls right out - Take off a total of 6 or 8 screws that are on each side of the radio - HU comes right out with harness attached in the back Not sure about nav bezel, if it's the same as the cubby holy w/air vent, it also just kind of pops out... Link to comment Share on other sites More sharing options...
OGHK87Jay Posted November 30, 2011 Author Share Posted November 30, 2011 Saweeet sounds easy going to do it this weekend to retreive my ring I hope its still there. Thank you!!! and much appreciated!! Link to comment Share on other sites More sharing options...
Drift Motion Posted November 30, 2011 Share Posted November 30, 2011 you're welcome just don't force anything and if you need pictures, I'm sure there's a thread floating around here that has pictures Link to comment Share on other sites More sharing options...
OGHK87Jay Posted November 30, 2011 Author Share Posted November 30, 2011 Thanks for the warning or I actually would of bruted the side trims. Guess I'll have to do this with finesse. Link to comment Share on other sites More sharing options...
mr.hicksta Posted November 30, 2011 Share Posted November 30, 2011 It's easier to get the wood trim off if you remove the shifter surround first. Be careful with the retaining clips on the trim as well. They can fall off easily. Link to comment Share on other sites More sharing options...
OGHK87Jay Posted November 30, 2011 Author Share Posted November 30, 2011 Roger that!! Thanks I'll do that first Link to comment Share on other sites More sharing options...
OGHK87Jay Posted November 30, 2011 Author Share Posted November 30, 2011 Actually how do I go about doing that? Link to comment Share on other sites More sharing options...
mr.hicksta Posted November 30, 2011 Share Posted November 30, 2011 Remove shift knob, and reach under the corners of the shift boot and pull up lightly. Once you get all 4 corners off, disconnect the cig lighter and you're good to go. Link to comment Share on other sites More sharing options...
OGHK87Jay Posted November 30, 2011 Author Share Posted November 30, 2011 Awesome thanks I hope this is the same as for the 5eat cuz I gots a 5eat Link to comment Share on other sites More sharing options...
mr.hicksta Posted November 30, 2011 Share Posted November 30, 2011 I don't think it'll be too much different, but I can't say for sure because I have an MT. Link to comment Share on other sites More sharing options...
bmx045 Posted November 30, 2011 Share Posted November 30, 2011 watch out for the screws holding the center trim on on either side of the si drive badge (underneath) Link to comment Share on other sites More sharing options...
OGHK87Jay Posted December 1, 2011 Author Share Posted December 1, 2011 center trim as in ? This is turning out to be a bigger bitch to pull off the trim. I started from the top close to the radio and a/c console that part comes out but then when i try to get the bottom part where the shifter is it wont budge at all. Link to comment Share on other sites More sharing options...
proflatlander15 Posted December 1, 2011 Share Posted December 1, 2011 My wood trim is held on by clips AND a screw. You have to remove the shift boot before removing the wood trim. After that, it is very self explanatory. Link to comment Share on other sites More sharing options...
OGHK87Jay Posted December 1, 2011 Author Share Posted December 1, 2011 Like i said im a 5eat unless i just dig into the center were the shifters track is and just rip that out first. Link to comment Share on other sites More sharing options...
bmx045 Posted December 1, 2011 Share Posted December 1, 2011 You need to remove the shifter surround/ash tray piece off in order to get the console trim off at the bottom. The shifter surround and ashtray piece snaps in, just pry an edge and lift towards the sunroof Link to comment Share on other sites More sharing options...
bmx045 Posted December 1, 2011 Share Posted December 1, 2011 And so do I... The shifter PRND is not apart of the bezel around the chrome trim. First pull the chrome trim up and off and then pry the edge below the si drive badge and pull up and out. Reply when youve done atleast this, I'll hold your cyber hand Link to comment Share on other sites More sharing options...
shoop Posted December 1, 2011 Share Posted December 1, 2011 Not sure if you still need it, but here is a manual for radio removal. Only the first few pages apply, but it helped me out with my 05. http://www.pdfhost.net/index.php?Action=Download&File=2ab9e87d49fc93ae1c4ef03bca5bb7c9 Link to comment Share on other sites More sharing options...
OGHK87Jay Posted December 7, 2011 Author Share Posted December 7, 2011 thanks this makes it a hell of alot easier Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.