![](http://content.invisioncic.com/o321498/set_resources_3/84c1e40ea0e759e3f1505eb1788ddf3c_pattern.png)
Harsho1
-
Posts
66 -
Joined
Content Type
Profiles
Forums
Gallery
Posts posted by Harsho1
-
-
I have a 2105 legacy 3.6R, and am looking to replace the harness that plugs into the four O2 sensors. In the FSM the connectors are labeled E24, E25, E47, & E61 . On page WI-475 it looks like they should all be part of the transmission harness, but in the catalog the main trans harness is listed as 24031AA510, and the inhibitor harness is 31911AA030 . Neither one of these look like they have the connectors on them.
-
-
-
-
2005, SUBARU LEGACY 2.5GT
REGAL BLUE PEARL (DARK BLUE)
147K MILES
5EAT - 5 SPEED ELECTRONIC AUTOMATIC TRANSMISSION
CLEAR TITLE IN HAND
NO LEIN
LOCATED IN FORT WAYNE, INDIANA
VIN : 4S3BL676654217114
EMAIL : HARSHO134@GMAIL.COM
ASKING PRICE $4000.00
ENGINE RUNS, BUT HAS BAD KNOCK. BRING A TRAILER
LOTS OF UPGRADES AND EXTRAS.
TEIN FLEX Z COILOVERS
ALL EXHAUST IS AFTERMARKET STAINLESS (HEADERS, UP-PIPE, DOWN-PIPE, AND CAT-BACK ARE ALL AFTERMARKET.
STOCK VF-40 REPLACED WITH VF-52
FT LOWER CNTRL ARMS REPLACED WITH SPEC-B STYLE ALUMINUM ARMS.
ALL REAR ARMS REPLACED WITH AFTERMARKET ADJUSTABLE (WHITELINE AND MEGAN RACING)
BOTH SWAYBARS REPLACED WITH WHITELINE ADJUSTABLE.
ALL HOSES IN ENGINE REPLACED WITH AUTOBAHN88 BLUE SILICONE HOSE KIT
PERRIN LIGHTWEIGHT CRANK PULLEY, BATTERY HOLD DOWN, INTAKE HOSE, AFTA MAF HOSE, PITCH STOP MOUNT
MISHIMOTO COOLANT OVERFLOW TANK
DAMD FLATBOTTOM STEERING WHEEL (NOT INSTALLED)
MANUAL TRANSMISSION STEERING WHEEL AUDIO CONTROL SWITCHES (NOT INSTALLED)
NEW WEATHERTECH FLOORLINERS (INSTALLED ABOUT 3 MONTHS OF USE)
MOTOROLLA BLUETOOTH ADDED TO FACTORY STEREO
ONE SET OF FACTORY WHEELS CUSTOM POWDER COATED GUNMETAL GRAY WITH BRIDGESTONE BLIZZAKS
ONE SET OF MILLE MIGILIA WHEELS CUSTOM POWDER COATED THE SAME GUNMETAL GRAY WITH MICHELIN PILOT CUP 4S
COMPLETE POWERSTOP ROTOR, CALIPER, AND PAD KIT, AND GOODRIDGE BRAIDED STAINLESS BRAKE HOSES
-
-
-
-
I am in the middle of putting my 05 back together with the Perrin inlet. I had a HUGE problem with their provided PCV connector as It was twice as tall as the factory one and then had the electrical connector on the top, instead of the side. There is NO WAY it was going to fit under the intake. I ended up cutting the factory one out of the old inlet tube and adding a 1/2" nipple to the bottom of it so I could use it on the Perrin tube.
-
Looking to install a remote start in my '05 LGT but don't really want to cut any underdash wiring. Any one know of a source for male and female connector sets for i84 , B280 , B281 , B69 & B72 connectors?
-
In the pictures i have seen, it appears they have moved to using a framed door window instead of frameless like on my fourth gen. This should help with wind noise immensely.
-
How do they feel to those that got around to installing them "as is" or close to it? Trying to gauge if I want to start swapping bushings in them before spring when they go on.
My old lca's were original, and bushings were torn in half, so I noticed a HUGE improvement. Since I paid less for both LCA's than I would for one bushing it was worth it.
-
So... has anyone actually installed these yet? I am still saving up for swaybar endlinks, and cv axles.
-
-
Looks like carid fixed or ended all their ebay auctions too. Seems now best price for these is rock auto at $106 ea.
-
My UPS tracking shows I should have them tomorrow. Will post pics A.S.A.P.
-
The eBay post in op lists fitments on some Ford transit connect so I think they have a listing error. The part number listed is for LGT lca but their information is for some Ford part that only lists for $5.00. My two arms shipped in one box that ups says weighs about 19 pounds.
-
So... My lca bushings have been getting a little sloppy and I had been saving up for new bushings...I had wished I could afford the spec-b arms, but at over $300 a piece that was WAY out of my budget. Then I found some on rock auto that are spec-b style for only $106 ea. Jackpot!!!
Then I thought I would double check E-bay to see if I could find them for cheaper.
-WOAH-
I don't know if this is some kind of typo but I ordered both sides (cms80181 is other side).
their listing says it fits a ford transit connect, but on rock auto it fits LGTs, also picture looks like a spec-b style arm.
So in conclusion, I got TWO front spec-b style LCA's for $45.00 shipped.
yes $45.00 for BOTH with SHIPPING!
I should have them on thurs. the 18th and will post results.
Help finding part number for wiring harness(es)
in Sixth Generation Legacy (2015 -2019 )
Posted
That does look correct. I guess I should have looked a little harder in the exhaust diagram! I will order one in and see if that is it!